Solar Wall Light Outdoor — 72 LED Motion Sensor, 4 Lighting Modes, 3600mAh, IPX5 Waterproof
Solar Wall Light Outdoor — 72 LED Motion Sensor Sconce
Light on the path before you reach the door. A monocrystalline panel charges through the day; after dark the light switches itself on, and a PIR sensor lifts it to full brightness the moment someone steps within six metres.
- 72 × SMD2835 LEDs behind a double-layer PC shade — even, glare-free spread with no hot spots
- Four lighting levels: dim + motion boost, dark + motion boost, always bright, always dim
- 3600mAh built-in battery (2 × 18650) — 6–12 hours of run time from a 4–6 hour charge
- IPX5 sealed housing with a rubber gasket ring — rain, dew and dust stay out
- White light 6000–6500K or warm light 2800–3500K — pick the tone at checkout


Even brightness you can sit under
The PC shade diffuses the 72 LEDs into a flat, wide wash instead of a hard cone, so a patio table or a doorway stays usable after sunset.

Built for the rainy season
A rubber gasket ring seals the housing at every joint, and the panel is machine-laminated rather than taped. Tested against rain, thunderstorms and snow — the light keeps running when the weather turns.

Dusk to dawn, automatically
A built-in photosensitive sensor does the switching: charging by day, lit at night. No timer to reset, no app, no switch to remember.

No wiring, no electricity bill
The 5V / 2.2W monocrystalline panel converts more of the day's light into stored charge than the polycrystalline panels common at this price, so it recovers faster after overcast weather.

Six metres of warning
The PIR sensor picks up movement up to 6 metres away across a 120° field — enough to light a driveway, a gate pillar or a side path before anyone reaches the door.

Four lighting levels
- Level 1 — dim standby, jumps to full brightness on detection
- Level 2 — dark standby, full brightness on detection (longest runtime)
- Level 3 — constant high brightness, sensor off
- Level 4 — constant low brightness, sensor off

Specifications

- Model: YH0632-PIR
- Solar panel: monocrystalline silicon, 5V / 2.2W
- Battery: 3.7V / 1800mAh × 2 (18650) — 3600mAh total
- Light source: 72 × SMD2835, 0.2W each
- Colour temperature: 2800–3500K (warm light) / 6000–6500K (white light)
- Working time: 6–12 hours · Charging time: 4–6 hours
- Motion sensing: up to 6 m, 120° detection angle
- Waterproof rating: IPX5 (data sourced from the manufacturer's own laboratory)
- Material: ABS + PC · Colour: black housing with off-white shade
- Dimensions: 22.3 × 9.1 × 14.8 cm
- Packing: inner box 23.5 × 16 × 10.5 cm, 0.82 kg
What's in the box
1 × solar wall light, mounting bracket, 3 × screws, 3 × wall plugs, user manual.


Where it works
Front doors and gate pillars, villa gardens, balconies, patio walls, fences, stairwells and exterior corridors — anywhere the panel can face open sky.

Two ways to mount it
Drill mount: mark the bracket, drill, fix the screws, then hang the light. Adhesive mount: arm the switch, apply 3M tape or nail-free glue (not included), press onto a clean flat surface. Either way takes a few minutes and needs no electrician.


Before you install
Point the panel at direct sunlight. Under a deep eave, indoors, or behind foliage the battery will not charge and the light will not run — that is the solar charging limit, not a fault. Turn the switch on before first use, or the panel will not store energy.
